| R-A2 |
Architectural |
002-fire-exit-code.pdf |
EMERGENCY EGRESS LIGHTING REQUIRED
Per 2014 OSSC 1006.1 the means of egress, including the exit discharge, shall be illuminated at all times the building is occupied. Per 1006.3 an emergency electrical power system is required. The illumination levels are to be at levels specified by 1006.2/1006.3.1 with the performance of the system to be field inspected. Per 1011, the exit sign layout must be visible from all directions and indicate the direction of egress. |
| R-A3 |
Architectural |
004-floor-plan.pdf |
Except as indicated in Section 2406.3.1 each pane of safety glazing installed in hazardous locations (2406.4) shall be identified by a manufacturer's designation specifying who applied the designation, the manufacturer or installer and the safety glazing standard with which it complies as well as the information specified in Section 2403.1. The designation shall be acid etched, sand blasted, ceramic fired, laser etched, embossed or of a type that once applied, cannot be removed without being destroyed. A label as defined in Section 202 and meeting the requirements of this section shall be permitted in lieu of the manufacturer's designation. (2014 OSSC 2406.3) |
| R-A4 |
Architectural |
004-floor-plan.pdf |
2014 OSSC 1008.1.9.1 Hardware: Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11 shall not require tight grasping, tight pinching or twisting of the wrist to operate. |
| R-A5 |
Architectural |
004-floor-plan.pdf |
Egress doors shall be readily openable from the egress side without the use of a key or special knowledge or effort. 2014 OSSC 1008.1.9 |
| R-A6 |
Architectural |
004-floor-plan.pdf |
2014 OSSC 1008.1.9.5 Unlatching: The unlatching of any door or leaf shall not require more than one operation. |
| R-A7 |
Architectural |
002-fire-exit-code.pdf |
Doors serving rooms or spaces with an occupant load of 50 or more in Group A occupancy shall not be provided with a latch or lock unless it is panic hardware or fire exit hardware. (2014 OSSC 1008.1.10)
All door hardware to comply with 2014 OSSC 1008.1.9 |
| R-A8 |
Architectural |
005-east-sections.pdf |
Fireblocking shall be provided in concealed spaces of stud walls and partitions, including furred spaces, and parallel rows of studs or staggered studs, as follows:
1. Vertically at the ceiling and floor levels.
2. Horizontally at intervals not exceeding 10 feet.
2014 OSSC 718.2.2 |
| R-A9 |
Architectural |
009-lav-plans-ada.pdf |
Walls and partitions within 2 feet of service sinks, urinals and water closets shall have a smooth, hard, non absorbent surface, to a height of not less than 4 feet above the floor, and except for the structural elements, the materials used in such walls shall be of a type that is not adversely affected by moisture. 2014 OSSC 1210.2.2 |
| R-A10 |
Architectural |
010-electrical.pdf |
Per AOR exit signage is existing in the Kids assembly area and shall be field verified. 2014 OSSC 1011.1 |
| R-A11 |
Architectural |
001-site-plan.pdf |
Per OAR 918-050-0170 Statewide Fee Methodology for Deferred Submittals : A fee charged for processing and reviewing deferred plan submittals shall be based on the value of the particular deferred portion or portions of the project, with a set minimum fee. This fee is in addition to the project plan review fee based on the total project value.
For the COE, this fee is determined to be an amount equal to 35% of the building permit fee calculated on the specific value of each deferred submittal item of the project, with a minimum fee of $192.00 for commercial .
Please provide the valuation for all deferred submittal work/items when they are submitted. |
| R-A12 |
Architectural |
002-fire-exit-code.pdf |
Deferred Submittal : : Manual fire alarm system that activates the occupant notification system in accordance with Section 907.5 shall be installed in Group A occupancies where the occupant load due to the assembly occupancy is 300 or more. 2014 OSSC 907.2.1 |
| R-A13 |
Architectural |
002-fire-exit-code.pdf |
Kids area and Nursery area are used only when the parents/guardians are present, i.e. attending church services. 2014 OSSC 308.6.2 |
| R-A14 |
Architectural |
010-electrical.pdf |
Deferred Submittal : : Emergency egress lighting for entire rooms with non-fixed seating (kids area, auditorium), exit hallway from auditorium, lobby exits, exterior landing at required exits. 2014 OSSC 1006.1. GEC |
| R-A19 |
Architectural |
storefront-shops.pdf |
Except as indicated in Section 2406.3.1 each pane of safety glazing installed in hazardous locations (2406.4) shall be identified by a manufacturer's designation specifying who applied the designation, the manufacturer or installer and the safety glazing standard with which it complies as well as the information specified in Section 2403.1. The designation shall be acid etched, sand blasted, ceramic fired, laser etched, embossed or of a type that once applied, cannot be removed without being destroyed. A label as defined in Section 202 and meeting the requirements of this section shall be permitted in lieu of the manufacturer's designation. (2014 OSSC 2406.3) |
| R-A20 |
Architectural |
storefront-shops.pdf |
2014 OSSC 1008.1.9.5 Unlatching: The unlatching of any door or leaf shall not require more than one operation. |
| R-A21 |
Architectural |
storefront-shops.pdf |
Egress doors shall be readily openable from the egress side without the use of a key or special knowledge or effort. 2014 OSSC 1008.1.9 |
| R-EN2 |
Energy |
008-details.pdf |
r-21 insulation at new interior auditorium partitions as these walls enclose a new conditioned space which was not previously conditioned. 2014 OEESC 502.1.1 |
| R-F1 |
Fire Protection |
001-site-plan.pdf |
*The fire alarm system shall be designed to OFC 907 and NFPA 72 standards. Shop drawings with equipment cut sheets, battery calcs and voltage drop calcs shall be submitted and approved prior to installation of the fire alarm system. OFC 901.2, OFC 907.1 |
| R-F2 |
Fire Protection |
001-site-plan.pdf |
*The address shall be provided on the building in a location which is plainly visible from the street, of contrasting color, a minimum of 4 inches in height. OFC 505.1 |
| R-F3 |
Fire Protection |
001-site-plan.pdf |
*Sprinkler changes of less than 15 heads or additions of less than 10 heads do not require a plan submittal but must comply with nationally recognized standards. The modifications are cumulative and all modifications on all floors are considered in the 15 head limit. Provide basic as-built plans, a service report, and sprinkler certification form at the time of final inspection. If 15 or more heads modified or more than 10 added then a complete fire sprinkler submittal is required. Any sprinkler heads that are damaged or painted are required to be replaced with new sprinkler heads. Sprinklers on the project shall be quick response for the change to light hazard OFC 901.2 |
| R-F4 |
Fire Protection |
001-site-plan.pdf |
*Submit emergency plans as per OFC 404 through 408 for Fire Marshal's review and approval prior to Final Fire inspection. Plans are required for A, E, H, I, R (university/college bldgs), SR, high-rise buildings, atriums, and some M occupancies. OFC 404
Emergency Planning and Preparedness guide (PDF) can be downloaded from http://www.eugene-or.gov/index.aspx?NID=341 |
| R-F5 |
Fire Protection |
001-site-plan.pdf |
* Per 1028.12 of the OFC the seats in the assembly space shall be fastened together in groups of not less than 3 or be fixed to the floor |
| R-F6 |
Fire Protection |
001-site-plan.pdf |
*Supra Brand is the only approved lock box. The lock box may be purchased locally at National Fire Fighter Corporation, Omlid and Swinney or the Supra Company in Salem at 1-800-547-0252. OFC 506.1 |
| R-F7 |
Fire Protection |
SUMMIT CREEK SUBMITTAL FP.1.pdf |
Return bends are required from dry systems per 7.2.2(3) NFPA 13. It looks like the line diagram detail shows this so this is just a note |
| R-M1 |
Mechanical |
012_M0.0.pdf |
Equipment and appliances shall be installed as required by the terms of their approval, in accordance with the conditions of the listing, the manufacturer’s installation instructions and this code. Manufacturer’s installation instructions shall be available on the job site at the time of inspection. 2014 OMSC 304.1 |
| R-M2 |
Mechanical |
017_M2.1.pdf |
When duct work is located outside the building a minimum R-8 value is required. 2014 OEESC 503.2.7 |
| R-M3 |
Mechanical |
012_M0.0.pdf |
Balance report to be on site for Inspector. 2014 OMSC 403.1, 102.4 |
| R-S2 |
Structural |
Summit Creek Church Mechanical.pdf |
SPECIAL INSPECTION FOR POST INSTALLED EPOXY/EXPANSION/SCREW-TYPE ANCHORS IS REQUIRED IN ACCORDANCE WITH LATEST CODE APPROVAL REPORT. (OSSC 1705) |
